Attention! The text in this document has been recognized automatically. To view the original document, you can use the 'Original mode'.
Thank you for your purchase of this quality Wireless Thermo
Clock. The utmost care has gone into the design and
manufacture of your clock. Please read these instructions
carefully and store them in a safe place for future
reference.
The Wireless Thermo Clock has a clear, easy-to-read
display that shows the time, month, date, day of the
week, indoor temperature and outdoor temperature. The
Wireless 915 MHz technology a l l o w s y o u t o place
the sensor anywhere you like. The Temperature is
measured and transmitted from the remote sensor. It is able
to receive and display readings from up to 2 sensors.
With the Radio controlled function, the current time and
calendar are automatically synchronized with the
Nov 01, 2008 I happen to have the same model clock. All you need to do is wait until the clock automatically connects with the broadcast from the atomic clock in Colorado and adjusts the time itself (the clock automatically connects at 2:00 AM). If you want to set it immediately, however, you can press the RECEIVE button to connect.
Clock is on the wrong time zone. Clock instructions spc373, sharp atomic clock instructions spc364, sharp atomic clock instructions. Sharp spc364 atomic clock instructions - Rage will turn sex story bhai behan. The only buttons are for 4 time zones and a reset. I have a Sharp SPC373 Atomic clock every 2 years the batteries die and I can never find. Jul 10, 2018 Radio Controlled (Atomic) Wall Clock setup First of all, it is not an atomic clock, instead, it receives the radio signal from an atomic clock which is located near Fort Collins, Colorado.
time signal transmitted from the atomic clock in FT.
Collins, Colorado. USA (WWVB)
MAIN FEATURES:
1^38!;
ft^гyllllOfkllliS
-13
-14
-15
1. CLOCK WINDOW:
- Displays time, year, signal strength indicator, daylight
savings time (DST), alarm icons and time zone map.
2. CALENDAR, DAY AND TEMPERATURE WINDOW:
- Displays the month, date, day of the week as well as
Sharp Model Spc364 Manual
the indoor & outdoor temperature.
3. SNOOZE BUTTON:
- Press it to stop the current alarm when it is sounding.
Attention! The text in this document has been recognized automatically. To view the original document, you can use the 'Original mode'.
3.
Press the “UP” or “DOWN” button to change its value.
4.
Press the “ALM ON/OFF” key once until the alarm
Minute digit flashes.
5.
Press the “UP” or “DOWN” button to change its value.
6.
Press the “ALM ON/OFF” button to save and exit the
setting mode, or let it exit automatically 30
seconds later without pressing any key.
NOTE:
1.
The alarm will be automatically turned on when you
set the alarm time.
2.
The dual-alarm (alarmi & alarm2) design of this unit
provides you with more convenience, and you can set
two-alarm time if needed.
USING ALARM & TEMPERATURE PRE^LARM FUNCTIONS
1. Set the alarm time as the above section with alarmi
(alarm2) turned on when you set the alarm time.
Sharp Atomic Clock Instructions
2. In alarmi (alarm2) time mode, press the
“ALM ON/OFF” button once to turn on the temperature
pre-alarm with the icon displayed.
3. Press it again to turn off both of them until the icons
disappear.
NOTE:
1. To turn on temperature pre-alarm, ALARM must be on.
11
2.
The temperature pre-alarm can sound 30 minutes
earlier than the alarm only when the outdoor
temperature is below 26.0°F (-3.0°C).
3.
If no buttons are pressed during the alarm period, the
clock will enter the snooze mode automatically.
Besides, you can also press the “SNOOZE” button
once to stop the current alarm and activate the
snooze function.
4.
Once the snooze function is activated, the 4-step
crescendo alarm will sound 13 times in 5-minute
interval. The alarm duration is 60 seconds.
VIEWING THE TRANSIVimERCHANNEL
The default channel is Channel 1. Press the “CHANNEL”
button to view the channels from 1 to 2.
Press and hold the “CHANNEL” button for 2 seconds to
show the channels automatically; press it once again to
exit the automatic display mode.
HOW TO READ THE TEMPERATURE RECORDS
Press the “°C/°F” button to change the temperature unit
from °C for Celsius to °F for Fahrenheit.
Sharp Spc325 Atomic Clock Instructions
NOTE:
1. If no signals are received or the transmission is
interfered, ” will appear on the LCD.
12